Frequency bands
EGSM 900, GSM 1800
Compliant to GSM Phase 2/2+
GSM class: Small MS
Transmit power:
Class 4 (2W) at EGSM 900
Class 1 (1W) at GSM 1800
GPRS connectivity
GPRS multi-slot class 10
GPRS mobile station class B
Data Services
GPRS data downlink transfer: max. 85.6 kbits/s
GPRS data uplink transfer: max. 42.8 kbits/s
Support of PAP (Password Authentication Protocol) and CHAP (Challenge Handshake Authentication Protocol) for PPP connections
Support of PBCCH (Packet Switched Broadcast Control Channel) for enhanced GPRS performance
CSD transmission rates: 2.4, 4.8, 9.6, 14.4 kbits/s, non-transparent, V.110
WAP compliant
Internet services: TCP, UDP, HTTP, FTP, SMTP, POP3
SMS
MT, MO, CB, Text and PDU mode
SMS storage: SIM card plus 25 SMS locations in the mobile equipment
Transmission of SMS alternatively over CSD or GPRS (user-defined)
MMS compliant
Fax: Group 3, Class 2
Onboard SIM card interface
Supported SIM card: 3V
Coding scheme CS 1, 2, 3, 4
Optical isolation: 1kV DC
One antenna connector at front panel
For the use of an external antenna
Rugged screw connection
Please note that MEN does not offer SIM cards or mobile telephony contracts!
GPS Interface
20-parallel-channel GPS (Global Positioning System) receiver
GPS Band/Code: L1 frequency, C/A code
Integrated TCXO, RTC
Horizontal accuracy: better than 2.1m (CEP) 5.2m 2dRMS
Time To First Fix (TTFF):
Cold start: 34s typ.
Warm start: 32s typ.
Hot start: 0.5s typ.
Sensitivity:
Acquisition: -155dBm
Navigation: -157dBm
Tracking: -159dBm
GPS modes
TricklePower™ mode for power saving
Push-To-Fix™ mode
Protocol: NMEA 0183
SiRF® binary messages: altitude, longitude, elevation, velocity, heading, time, satellite tracking status, command/control messages
SiRF® binary interface: raw data
Antenna voltage supervision
3GPP compliance
Optical isolation: 1kV DC
One antenna connector at front panel
For the use of an external active antenna
Rugged screw connection
UARTs
Two channels
Accessible via onboard connectors
Physical interface at front panel using SA-Adapters™
Two SA-Adapters™ can be directly plugged within 4HP
Different physical layers depending on SA-Adapter™: RS232, RS422, RS485 with or without optical isolation
SA-Adapters™ to be ordered separately
Data rates up to 2 Mbits/s
60-byte transmit/receive buffer
Handshake lines: full support; lines depend on SA-Adapters™
Front Connections
Two Reverse SMA antenna connectors
Two cut-outs for SA-Adapters™
FPGA
Standard factory FPGA configuration:
Main bus interface
16Z057_UART - UART controller (controls in-system GSM-R/GPS communication and UARTs)
16Z045_FLASH - Flash interface
The FPGA offers the possibility to add customized I/O functionality. See FPGA.
CompactPCI® Bus
Compliance with CompactPCI® Core Specification PICMG 2.0 R3.0
Peripheral slot
32-bit/33-MHz PCI-to-PCI bridge
V(I/O): +3.3V
Electrical Specifications
Supply voltage/power consumption:
Depends on mounted SA-Adapters™ and used functions
+5V (-3%/+5%), 1900mA max.
+3.3V (-3%/+5%), 850mA max.
MTBF: 189,239h @ 40°C according to IEC/TR 62380 (RDF 2000)
Mechanical Specifications
Dimensions: conforming to CompactPCI® specification for 3U boards
Front panel:
4HP with ejector
3U single-slot front panel for two antenna and up to two UART connectors
Weight: 170g
Environmental Specifications
Temperature range (operation):
-40..+85°C for all functions except GSM-R (screened)
GSM-R component only operable in -20..+70°C range (auto on/off)
Airflow: min. 10m³/h
Temperature range (storage): -40..+85°C
Relative humidity (operation): max. 95% non-condensing
Relative humidity (storage): max. 95% non-condensing
Altitude: -300m to + 3,000m
Shock: 15g/11ms
Bump: 10g/16ms
Vibration (sinusoidal): 2g/10..150Hz
Conformal coating (standard)
Safety
PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers
EMC
Tested according to EN 55022 (radio disturbance), IEC1000-4-2 (ESD) and IEC1000-4-4 (burst)
Software Support
Driver software for Windows®, Linux, VxWorks®
For more information on supported operating system versions and drivers see Software.
Contact us
My MEN
You are logged off
Log in
Overview
This product is designed to work under Linux. See below for potentially available separate software packages from MEN.
This product is designed to work under Windows®. See below for potentially available separate software packages from MEN.
This product is designed to work under VxWorks®. For details regarding supported/unsupported board functions please refer to the corresponding software data sheets.
This product is designed to work under QNX®. For details regarding supported/unsupported board functions please refer to the corresponding software data sheets.
RSS Feeds
