Log in News & Media | Downloads | Corporate | Careers | Legal Notes
+49 911 99 33 5-0
info@men.de

EM1N - Embedded System Module COM with MPC5200B

Computer-On-Module

The EM1N Computer-On-Module is an MPC5200B PowerPC based embedded SBC for use in different industrial environments, with custom I/O in an onboard FPGA and front connectors.

Download data sheet

  • EM1N Product ImageEM1N Embedded System Module COM with MPC5200B
  • EM1N Product Image

Main Features

  • MPC5200B / 384 MHz
  • FPGA 18,752 LEs (225,000 gates)
  • Up to 256 MB onboard DDR SDRAM
  • Up to 8 MB boot Flash, NAND Flash
  • 2 MB SRAM, 16 MB additional SDRAM
  • Dual Ethernet, COM, USB 1.1 (front)
  • Dual CAN controller on carrier
  • User defined I/O functions (COMs, graphics, IDE etc.) optional via FPGA on carrier
  • Stackable with PCI-104
  • MENMON BIOS for PowerPC cards
  • -40°C to +85°C qualified
EM1N Product Image

Technical Data

CPU
PowerPC
  • MPC5200B
  • Up to 400MHz
Memory
  • 2x16KB L1 data and instruction cache integrated in MPC5200
  • Up to 256MB SDRAM system memory
    • Soldered
    • DDR
    • 64MHz memory bus frequency
  • Up to 1GB soldered NAND Flash (and more), FPGA-controlled
  • 16MB additional SDRAM, FPGA-controlled, e.g. for video data and NAND Flash firmware
  • Up to 8MB boot Flash
  • 2MB battery-backed SRAM, or: 128KB non-volatile FRAM
  • Serial EEPROM 8kbits for factory settings
Mass Storage
  • Parallel IDE (PATA)
    • One port for hard-disk drives
    • Available via I/O connector
    • FPGA-controlled
  • Up to 1GB soldered ATA NAND Flash (and more), FPGA-controlled
Graphics
  • Available via I/O connector
  • FPGA-controlled
I/O
  • USB
    • One USB 1.1 port
    • Series A connector at front panel
    • OHCI implementation
    • Data rates up to 12Mbit/s
  • Ethernet
    • Two 10/100Base-T Ethernet channels
    • One channel FPGA-controlled
    • Two RJ45 or one D-Sub connector at front panel
  • One RS232 UART (COM1)
    • RJ45 or D-Sub connector at front panel
    • Data rates up to 115.2kbit/s
    • 512-byte transmit/receive buffer
    • Handshake lines: CTS, RTS
  • CAN bus
    • Two CAN bus channels
    • 2.0 A/B CAN protocol
    • Data rates up to 1 Mbit/s
    • Connection via onboard connectors
    • External transceivers using SA-Adapters
  • Further I/O depending on FPGA configuration
FPGA
  • Standard factory FPGA configuration:
    • Main bus interface
    • 16Z070_IDEDISK - IDE controller for NAND Flash
    • 16Z043_SDRAM - Additional SDRAM controller (16MB)
    • 16Z023_IDENHS - IDE controller (PIO mode 0; non-hot-swap)
    • 16Z044_DISP - Display controller (800 x 600, 60Hz/70Hz, 6-bit RGB)
    • 16Z031_SPI - SPI touch panel controller
    • 16Z087_ETH - Ethernet controller (10/100Base-T)
    • 16Z025_UART - UART controller (controls COM10..COM13)
    • 16Z034_GPIO - GPIO controller (7 lines)
  • The FPGA offers the possibility to add customized I/O functionality. See FPGA.
PCI Interface
  • 32-bit, 32-MHz PCI interface at PCI-104 connector J1
  • Compliant with PCI Specification 2.2
  • Support of 4 external masters
Miscellaneous
  • Real-time clock
  • Power supervision and watchdog
Electrical Specifications
  • Supply voltage/power consumption:
    • +5V (-2%/+5%), 10mA max., only for USB
    • +3.3V (-2%/+5%), 1A typ.
  • MTBF: 232,000h @ 40°C (derived from MIL-HDBK-217F)
Mechanical Specifications
  • Dimensions: conforming to ESM specification (PCB: 149mm x 71mm), Type I-S
  • Weight: 90g (w/o heat sink)
Environmental Specifications
  • Temperature range (operation):
    • -40..+85°C
    • Airspeed: min. 2 m/s
  • Temperature range (storage): -40..+85°C
  • Relative humidity (operation): max. 95% non-condensing
  • Relative humidity (storage): max. 95% non-condensing
  • Altitude: -300m to + 3,000m
  • Shock: 15g/11ms
  • Bump: 10g/16ms
  • Vibration (sinusoidal): 2g/10..150Hz
  • Conformal coating on request
Safety
PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers
EMC
Tested according to EN 55022 (radio disturbance), IEC1000-4-2 (ESD) and IEC1000-4-4 (burst)
BIOS
MENMON
Software Support
  • VxWorks
  • Linux (ELinOS)
  • QNX
  • PikeOS (partitionable RTOS) certified platform
  • MSCAN/Layer2 support: MEN Driver Interface System (MDIS for all supported operating systems)
  • For more information on supported operating system versions and drivers see Software.

FPGA

Options

CPU
MPC5200B, 384 MHz
Memory
  • System RAM
    • 128 MB or 256 MB
  • NAND Flash
    • 0 MB up to maximum available
  • Boot Flash
    • 2 MB, 4 MB or 8 MB
  • Additional SDRAM
    • 0 MB or 16 MB
  • SRAM
    • 0 MB or 2 MB
  • 128KB non-volatile FRAM instead of SRAM
I/O
Front connections
  • D-Sub connectors for Ethernet and COM/USB
Mechanical
PCI and I/O connectors can also be placed for face-to-face assembly (ESM Type N)
Some of these options may only be available for large volumes.
Please ask our sales staff for more information.

Ordering Information

Standard EM1N Models
15EM01N00

MPC5200B/384MHz, FPGA 18,752 logic elements, 256 MB SDRAM, 1 GB NAND Flash, 2 MB SRAM, 16 MB graphics memory, 2 MB boot Flash, front: 2 Fast Ethernet (RJ45), 1 UART (RJ45), 1 USB, -40..+85°C with qualified components (also for ESM evaluation kit EK6N)

Miscellaneous Accessories
05F006-00

RS232 interface cable RJ45 to 9-pin D-Sub (1 COM to 1 COM), 2m

Software

Linux
13Z025-90

Linux native driver (MEN) for 16Z025_UART, 16Z057_UART and 16Z125_UART

13Z077-90

Linux native driver (MEN) for 16Z077_ETH and 16Z087_ETH

This product is designed to work under ELinOS Embedded Linux by SYSGO. For more information and product support please contact www.sysgo.com.

13Z016-06

MDIS5 driver (MEN) for 16Z029_CAN (CANopen master)

10EM01-90

Linux BSP (MEN) for EM1, EM1A, EM1N, EK6, EK6N, F12, F12N and PP1 under ELinOS 5.0 (rpm for direct installation in ELinOS)

13MD05-90

MDIS5 System (and Device Driver) Package (MEN) for Linux. This software package includes most standard device drivers available from MEN.

VxWorks
13Z025-60

VxWorks native driver (MEN) for 16Z025_UART, 16Z057_UART and 16Z125_UART

13Z017-06

MDIS5 low-level driver sources (MEN) for 16Z034_GPIO, 16Z037_GPIO and 16Z127_GPIO

13Z016-06

MDIS5 driver (MEN) for 16Z029_CAN (CANopen master)

10EM01-60

VxWorks BSP (MEN) for EM1, EM1A, EM1N, EK6, EK6N, F12N and F12

10EM01-61

VxWorks 6.8 BSP for EM1A and EM1N

13Z015-06

MDIS5 low-level driver sources (MEN) for 16Z029_CAN (MSCAN/Layer2)

QNX
10EM01-40

QNX 6.3 SP3 BSP (MEN) for EM1, EM1A, EM1N, EK6, EK6N, F12 and F12N

13Z025-40

QNX 6.3 native driver (MEN) for 16Z025_UART and 16Z125_UART

13Z025-41

QNX 6.4 native driver (MEN) for 16Z025_UART and 16Z125_UART

13Z025-42

QNX 6.5 native driver (MEN) for 16Z025_UART and 16Z125_UART

13Z044-40

QNX native driver (MEN) for 16Z044_DISP (frame buffer)

13Z087-40

QNX native driver (MEN) for 16Z087_ETH

13Z017-06

MDIS5 low-level driver sources (MEN) for 16Z034_GPIO, 16Z037_GPIO and 16Z127_GPIO

13Z016-06

MDIS5 driver (MEN) for 16Z029_CAN (CANopen master)

10EM01-41

QNX 6.4.1 BSP (MEN) for EM1, EM1A, EM1N, EK6, EK6N, F12 and F12N

10EM01-42

QNX 6.5.0 BSP (MEN) for EM1, EM1A, EM1N, EK6, EK6N, F12 and F12N

13Z015-06

MDIS5 low-level driver sources (MEN) for 16Z029_CAN (MSCAN/Layer2)

PikeOS

This product is designed to work under PikeOS by SYSGO. PikeOS is a real-time operating system for use in safety and mission-critical systems which can be certified according to DO-178B DAL-B and EN 50128 SIL 4. For more information and product support please contact www.sysgo.com.

OS-9
13Z017-06

MDIS5 low-level driver sources (MEN) for 16Z034_GPIO, 16Z037_GPIO and 16Z127_GPIO

13Z016-06

MDIS5 driver (MEN) for 16Z029_CAN (CANopen master)

13Z015-06

MDIS5 low-level driver sources (MEN) for 16Z029_CAN (MSCAN/Layer2)

Firmware/BIOS
MENMON is an MEN firmware/BIOS for PowerPC platforms.
14EM01-00

MENMON (Firmware) for EM1, EM1A, EM1N, F12 and F12N (object code)